According to the statistics released by the Law Enforcement Supervision Department of the General Administration of Quality Supervision, Inspection and Quarantine, in the first half of 2017, China has implemented 143 recalls of defective automobile products, involving 4,760,100 vehicles, of which the airbag and seat belt problems were the main recall reasons, and the number of recalls was 47. The number of vehicles involved in the problem reached 1,563,600; followed by the engine problem, a total of 34 recalls, 1,296,800 vehicles involved in the problem; and the number of recalls of automobile products due to electrical equipment problems ranked third, recalled 7 times, involving problem vehicles 620,100 vehicles. In addition, there were recalls due to body problems, transmission problems, steering problems, etc., which led to the recall of 143 defective automobile products in China in the first half of the year. 1. Imported car recall
By alloying several percent of carbon with a minimum, 12 % alloy (primarily chromium), hard carbides are formed and dispersed throughout the surfacing deposit.
These dispersed carbides are much harder than the surrounding matrix and provide excellent abrasion resistance. They are used when the primary wear factor is abrasion. At the lower end of the carbon range (less than 3 %) the quantity of carbides is small compared to the matrix where they are dispersed.
These alloys exhibit good abrasive wear resistance while retaining good toughness. These carbide-surfacing alloys are used to resist a combination of abrasion and impact. As the carbon content increases (to as much as 7 %), in the carbide containing alloys, the abrasion resistance increases and the toughness decreases. This is due to the higher percentage of carbides. As carbides are undermined and knocked out by moving abrasive particles, additional carbides are uncovered to further resist abrasives and delay wear as shown in the diagram to the right.
The low carbon steel base plate enables the plate to be welded, bolted or studded to existing structures, while the hard facing provides the premier wear-resistant surface capable of working in all applicable service conditions at either ambient or elevated temperatures.
HP Wear Resistant Group offers various products of wear plates namely Cr-Carbide Weld Clad Plates, Smooth Surface CCO plate, Heat Treated Wear Plates (AR Plate or Q&T Steel), Casting Plates, Tungsten Carbide Coated Plates in various grade and multiple size options.
Due to its excellent properties, HP Wear Plates work for long-lasting service life and super performance, which are well applied to the industries like Cement Plant, Steel Mill, Mining Site, Power Generation, Construction where need combat with abrasion.
Weld Overlay Plate,Wear Plate, Composite Steel Plate, CCO Wear Plate, Bimetal Steel Plate HuiFeng Wear Resistant Group , https://www.hpwearsolution.com
In July, major auto companies continued to be responsible for consumers and recalled defective products. According to Gai Shi Automobile, from the AQSIQ Defective Product Management Center, in July this year, major auto companies submitted a total of 21 recall plans to the AQSIQ, involving 1,957,265 vehicles, including 1,643 domestically produced models. 108 vehicles and 314,517 imported cars. In terms of recall reasons, the airbag problem is still the main reason. For example, more than 680,000 domestic Mazda 6 vehicles recalled by FAW Car are related to airbag defects, and there are more than 230,000 problem models that BMW announced recalled. The following is the specific recall situation:
Domestic production model recall
1.2016 Dongfeng Nissan's new Tianzhu recall scale: 30,279 recall reasons: Due to the unreasonable selection of the brake light switch, it is unable to withstand large currents, and some vehicles may have ablation of the brake light switch. If you continue to use it, in extreme cases, the ablated switch will always be energized to cause continuous heating, which may cause the circuit at the switch to melt, increasing the risk of fire of the vehicle and posing a safety hazard.
Recall plan: Dongfeng Motor Co., Ltd. announced that from July 28, 2017, it will recall some of the 2016 Dongfeng Nissan brand new Tianzhu vehicles produced from June 17, 2016 to November 29, 2016, totaling 30,279 vehicles. Dongfeng Motor Co., Ltd. will replace the improved brake light switch for vehicles within the recall range to eliminate safety hazards.
2.2014-2016 Accord recall scale: 270,443 recall reasons: Due to supplier manufacturing reasons, external conductive liquid may invade the inside of the plated through hole of the battery sensor substrate and short circuit, resulting in burning of components, in extreme cases The engine compartment is on fire and there are safety hazards.
Recall plan: Starting from September 25, 2017, the 2014-2016 Accord sedan will be recalled from January 31, 2013 to November 3, 2015. After the recall, Guangqi Honda Automobile Co., Ltd. will use the battery for the vehicle. Sensors are replaced free of charge to eliminate safety hazards.
3.2014-2015 Lingpai recall scale: 350,560 recall reasons: Due to the manufacturer's manufacturing reasons, the external conductive liquid may invade the inside of the plating through hole of the battery sensor substrate and short circuit, resulting in burning of the component, in extreme cases It may cause fire in the engine compartment and pose a safety hazard.
Recall plan: Starting from September 25, 2017, the 2014-2015 Lingpai sedan produced during the period from January 24, 2013 to September 26, 2015 will be recalled. After the recall, Guangqi Honda Automobile Co., Ltd. will Battery sensors are replaced free of charge to eliminate safety hazards.
4. Dongfeng Honda Jade recalled scale: 140,876 recall reasons: Due to the manufacturer's manufacturing reasons, external conductive liquid may invade the inside of the plated through hole of the battery sensor substrate and short circuit, resulting in component burning, in extreme cases It may cause fire in the engine compartment and pose a safety hazard.
Recall plan: From September 25, 2017, recall the JADE car produced between November 14, 2012 and November 16, 2015. After the recall, Dongfeng Honda Automobile Co., Ltd. will replace the battery sensor of the vehicle for free to eliminate safety hazards.
5. BMW 320i, 325i, 320Li, 328Li, 335Li and X1
Recall scale: 28,676 recall reasons: The airbag of the vehicle is equipped with an ammonium nitrate gas generator without a desiccant produced by Takada. When the airbag is deployed, the gas generator may be abnormally damaged, causing debris to fly out and injuring the inside of the vehicle, posing a safety hazard.
Recall plan: Starting from November 13, 2017, recall some domestic Brilliance BMW 320i, 325i, 320Li, 328Li, 335Li and X1 vehicles produced between July 12, 2005 and December 26, 2012. After recall, BMW Brilliance Automobile Co., Ltd. will replace the airbag gas generator of the involved parts for the vehicle free of charge to eliminate safety hazards.
It is worth noting that this recall belongs to the recall of "Bringing BMW Automobile Co., Ltd. and BMW (China) Automobile Trading Co., Ltd. recalling some domestic and imported BMW cars" released on December 23, 2016 and February 6, 2017. change. Due to the extension of the supply of the recall airbag gas generator, the recall start time was changed from August 1, 2017 and October 9, 2017 to November 13, 2017. The original recall plan was voided and the information released this time will prevail. All losses arising from this change will be borne by BMW Brilliance Automotive Co., Ltd.
6. Chery Kay wing C3/C3R EMT "Smart Gear" type car recall scale: 5,549 recall reasons: due to clutch actuator and cable, gearbox control module software and gearbox wiring harness quality problems, resulting in vehicles When the gear shifts, the system may be misjudged, causing the vehicle fault light to illuminate, and the vehicle power is limited. In extreme cases, the gearbox will enter the neutral position, power interruption occurs, and there is a safety hazard.
Recall plan: From July 25, 2017, recall the EMT "Smart Gear" type of Chery Kay Wing C3/C3R produced from March 23, 2015 to March 30, 2017. After the recall, Chery Automobile Co., Ltd. will replace the TCU harness for the vehicle free of charge, update the TCU data, check the clutch actuator and cable status, and replace the clutch actuator and cable that do not meet the requirements to eliminate safety hazards.
7. Mazda's domestic Attz recall scale: 80,235 recall reasons: Due to the poor sealing structure of the rear wheel mechanical parking brake caliper dust cover, the inside of the brake caliper is filled with water and the roller part is rusted. Continued use in this case may result in poor sliding performance of the roller, declining parking brake force, and in some cases, slipping may occur, posing a safety hazard.
Recall plan: recalled some domestic Atuz cars produced from July 31, 2013 to June 29, 2016 from January 26, 2018. After the recall, FAW Car Co., Ltd. will carry out the roller of the vehicle. When detecting rust, replace the new brake caliper assembly; when no rust is found, replace the dust cover assembly to eliminate safety hazards.
8. Mazda 6
Recall scale: 680,642 recall reasons: The airbag of the passenger seat of the vehicle is equipped with an ammonium nitrate gas generator without a desiccant produced by Takada. When the airbag is deployed, the gas generator of the airbag may be abnormally damaged. , causing debris to fly out, hurting the inside of the car, there are security risks.
Recall plan: From March 19, 2018, recall some domestic Mazda 6 cars produced between September 18, 2008 and March 31, 2016. After the recall, FAW Car Co., Ltd. will replace the passenger-side air bag gas generators produced by other manufacturers for free to eliminate safety hazards.
9. Audi Q3
Recall scale: 55,848 recall reasons: Due to software errors in the gateway control unit, if an electronically controlled mechanical parking brake is used for emergency braking during driving, the brake light cannot be illuminated, and the rear vehicle cannot obtain the vehicle. The warning of braking increases the risk of the vehicle being rear-ended and there is a safety hazard.
Recall plan: From July 6, 2017, recall some of the domestic Audi Q3 models produced from November 7, 2015 to December 3, 2016. After the recall, FAW-Volkswagen Automotive Co., Ltd. will update the gateway control unit related software for vehicles free of charge to eliminate potential safety hazards.
2013 BMW 5 Series (standard wheelbase)
Recall scale: 1,559 recalls in the mainland Cause: Due to the supplier's production reasons, the reflectivity of the rear reflector of the vehicle is lower than the standard lower limit, resulting in the vehicle being found when the vehicle is turned off in low illumination and the vehicle is turned off. The possibility is reduced and there are security risks.
Recall plan: Since July 28, 2017, BMW (China) Automobile Trading Co., Ltd. plans to recall part of the imported 2013 BMW 5 Series (standard wheelbase) produced between January 30, 2013 and June 29, 2013. ) series of cars. After the recall, BMW (China) Automobile Trading Co., Ltd. will replace the rear reflector for the vehicle for free to eliminate defects.
2. BMW 120i, 130i, 316i, 320i, 325i, 330i, 335i, X1, X3, X5, X6, M3 and M6
Recall scale: 206,620 recall reasons: The airbag of the vehicle is equipped with an ammonium nitrate gas generator without a desiccant produced by Takada. When the airbag is deployed, the gas generator may be abnormally damaged, causing the debris to fly out. Injury to the inside of the car, there are security risks.
Recall plan: Starting from November 13, 2017, recalled some imported BMW 120i, 130i, 316i, 320i, 325i, 330i, 335i, X1, X3, which were produced from December 9, 2005 to December 22, 2012. X5, X6, M3 and M6 vehicles, after the recall, BMW (China) Automobile Trading Co., Ltd. will replace the airbag gas generators of the involved parts for free to eliminate safety hazards. Among them, for the X5 and X6 vehicles, the front airbags for the driver and the front passengers are involved; for other vehicles, the driver's front airbag is involved.
In addition, this recall is a change in the recall of "Bringing BMW Automobile Co., Ltd. and BMW (China) Automobile Trading Co., Ltd. recalled some domestically and imported BMW cars" released on December 23, 2016 and February 6, 2017. Due to the extension of the supply of the recall airbag gas generator, the recall start time was changed from August 1, 2017 and October 9, 2017 to November 13, 2017. The original recall plan was voided and the information released this time will prevail. All losses arising from this change will be borne by BMW (China) Automobile Trading Co., Ltd.
3.2016-2017 BMW M760Li
Recall scale: 271 recalls in mainland China Cause: Due to the supplier's reasons, the oil pipe of the left oil cooler was mixed with the wrong rubber pipe during production, resulting in the rubber pipe part and the metal joint part not being properly connected. Oil leakage may occur afterwards. Since the leakage position is close to the front brake, the braking performance of the vehicle may be affected, which increases the risk of accidents of the vehicle during driving, and there is a safety hazard.
Recall plan: From July 28, 2017, recall some of the imported 2016-2017 BMW M760Li series cars produced between August 18, 2016 and April 27, 2017. After the recall, BMW (China) Automobile Trading Co., Ltd. will replace the oil cooling circuit for vehicles free of charge to eliminate defects. Stock vehicles will be sold after missing defects.
It is worth noting that this recall belongs to the change of “BMW (China) Automobile Trading Co., Ltd. recalled some imported BMW M760Li series cars†released on May 2, 2017. The reason for the change was that BMW recalled the replaced old parts through the recycling analysis, and there were new discoveries about the root cause of the defects. Therefore, the scope of the recall was expanded and the maintenance plan was changed. Vehicles that have completed the original recall and need to re-complete this recall. The original recall plan was voided and the information released this time will prevail. All losses arising from this change will be borne by BMW (China) Automobile Trading Co., Ltd.
4.2012-2016 G-Class off-road vehicle recall scale: 5,173 recalls in mainland China Cause: Due to production deviation, the tightening torque of the universal joint fixing bolt at the bottom of the steering column does not meet the requirements, which may cause excessive wear of the universal joint. The accuracy of the steering is degraded; in some cases, the torque transmission between the steering wheel and the steering mechanism may be completely interrupted, causing the vehicle to be unable to turn, increasing the risk of collision of the vehicle and posing a safety hazard.
Recall plan: From August 5, 2017, recalled some imported 2012-2016 G-Class off-road vehicles produced from July 25, 2012 to January 20, 2017, including 5,173 in mainland China. Car. After the recall, Mercedes-Benz (China) Automobile Sales Co., Ltd. will replace the steering column bottom universal joint for free for vehicles to eliminate defects.
5.2015 Lincoln MKZ series recall scale: 316 recalls in mainland China Cause: Some vehicles in this recall range will not be able to reach the constraint due to the internal temperature generated by the seat belt pretensioner during the collision. The pull force required by the occupant may be disengaged from the front seat belt pretensioner cable on the driver's side and the passenger's side. This can result in the seat belt not fully restraining the occupant in the event of a collision of the vehicle, increasing the risk of injury to the occupant and posing a safety hazard.
Recall plan: Since September 30, 2017, part of the imported 2015 Lincoln MKZ series cars, which were produced from June 11, 2014 to July 31, 2014, will be recalled, including 316 vehicles in mainland China. After the recall, Ford Motor (China) Co., Ltd. will apply a sticky silicone coating to the vehicle's belt pretensioner cable to eliminate defects.
6.2007-2012 Outlander EX Jinjie series recall scale: 54,672 recalls in mainland China Cause: Due to the structural problem of the resin structure of the front windshield wiper motor with breathing holes, the moisture in the area of ​​the front windshield wiper cover It will drip from the periphery of the wiper motor and accumulate around the breathing hole of the motor. During the cooling process after the motor is running, rainwater will be sucked into the motor from the breathing hole, causing internal parts to rust, jam or circuit failure. In severe cases, the motor will stop running, affecting the driver's front view, and there are potential safety hazards.
Recall plan: From September 11, 2017, recalled some of the imported 2007-2012 Outlander EX Jinjie series cars produced from November 23, 2006 to September 27, 2012, including 54672 in mainland China. Car. After the recall, Mitsubishi Motors Sales (China) Co., Ltd. will replace the improved front windshield wiper motor assembly for vehicles to eliminate defects.
7. Hyundai 2012-2016 Shengda and Ge Rui series car recall scale: 26,124 recalls in mainland China Cause: Because the engine compartment cover locking device cable is made of galvanized steel, when the protective cover of the cable is broken off After the external moisture enters, the cable may corrode and adhere, resulting in poor operation of the engine compartment cover secondary locking device. The engine compartment cover may automatically open unexpectedly during the running of the vehicle, affecting the driver's line of sight and posing a safety hazard.
Recall plan: From July 24, 2017, recall some of the imported 2012-2016 Shengda and Ge Rui series cars produced from January 3, 2012 to April 26, 2016, including the Shengda series of car recalls. Part of the imported 2012-2015 Shengda series cars produced during 2012.1.3—2015.4.3, a total of 9502 vehicles; the Ge Rui series recalled some of the imports from 2012.8.7—2016.4.26 during 2012-2016 The annual Ge Rui series of cars, a total of 16,622 vehicles. After the recall, Hyundai Motor (China) Investment Co., Ltd. will replace the modified engine compartment cover locking device cable for free to eliminate defects.
8. 2012-2014 A, B and CLA series car recall scale: 16,301 recalls in the mainland Cause: Due to the manufacturer's manufacturing reasons, the brake booster vacuum pipe joints can not meet the durability requirements. When the vacuum pipe joint is damaged, the brake booster will no longer obtain vacuum, and the vacuum boost will be reduced. After braking for 2 to 4 times, the vacuum will be exhausted in the brake booster, the brake boost will disappear, and a larger need is needed. Power on the brake pedal. Since the driver cannot predict the loss of the brake boost, the risk of an accident may increase, and there is a safety hazard.
Recall plan: The recall will start from July 15, 2017, and some of the imported A-series cars of 2012-2014 will be produced during the period of 2012.6.30—2013.4.30, totaling 2,400; production during 2012.2.10—2013.2.12 Part of the import of the 2012-2014 B-class series of cars, a total of 13,988; during the period of 2013.4.22-2013.4.26, part of the imported 2012-2014 CLA-class series of cars, a total of three.
After the recall, Mercedes-Benz (China) Automobile Sales Co., Ltd. will replace the vacuum tube for free to eliminate defects. In addition, if the relevant user finds that the brakes are hard, please go to the nearest authorized dealer for disposal.
9. Aston Martin 2017 DB11
Recall scale: 111 recalls in mainland China Cause: The tire pressure monitoring system cannot trigger low pressure in time because the tire tire pressure monitoring module has incorrect code data, resulting in tire pressure lower than the minimum trigger pressure (1.9bar for front tire and 2.0bar for rear tire). Warning, there is a security risk.
Recall plan: Since August 1, 2017, some imported 2017 DB11 series cars will be recalled from November 9, 2016 to May 26, 2017, including 111 vehicles in mainland China. After the recall, Aston Martin Lada (China) Automobile Sales Co., Ltd. will update the code data of the tire pressure monitoring system module for vehicles free of charge to eliminate defects. Stock vehicles will be sold after the defect is eliminated.
10.2010-2011 Jaguar XJ
Recall size: 579 recall reasons: Due to production reasons, the auxiliary constraint control module software calibration will be reset to the initial state under certain circumstances. When the vehicle is subjected to a frontal collision, the front airbag may not be able to deploy normally as expected, increasing the risk of occupant injury and posing a safety hazard.
Recall plan: From July 14, 2017, we will recall some imported Jaguar XJ series cars from October 26, 2009 to September 22, 2010, and then Jaguar Land Rover (China) Investment Co., Ltd. The Auxiliary Constraint Control Module software will be upgraded for the vehicle to the latest version for free to eliminate defects.
11.2015 Jaguar XF SPORTBRAKE
Recall size: 791 recall reasons: Due to design reasons, the harness connection of the auxiliary restraint control module to the side impact sensor is incorrect. When the vehicle is in a position behind the B-pillar, the side air curtain may not be deployed or delayed, which increases the risk of injury to the rear passengers and poses a safety hazard.
Recall plan: Starting from July 14, 2017, we will recall some imported Jaguar XF SPORTBRAKE series cars from February 11, 2014 to October 2, 2015. Jaguar Land Rover (China) Investment Co., Ltd. will Reconnect the signal line to the correct side impact sensor for the vehicle to eliminate the defect.
12. Mazda Atosawa recalled scale: 2,000 recall reasons: Due to the poor sealing structure of the rear wheel mechanical parking brake caliper dust cover, the inside of the brake caliper is filled with water and the roller portion is rusted. Continued use in this case may result in poor sliding performance of the roller, declining parking brake force, and in some cases, slipping may occur, posing a safety hazard.
Recall plan: From January 26, 2018, recalled some imported Yasuzawa sedan produced between April 23, 2013 and November 6, 2013. After the recall, Mazda (China) Enterprise Management Co., Ltd. will roll the vehicle. When the shaft is tested and the rust is replaced, replace the new brake caliper assembly; when no rust is found, replace the dust cover assembly to eliminate safety hazards.
